Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat 500 key cover 500 is a handy way to open the doors and begin the car. However, there are numerous reasons why the fob won't be functioning. These include a dead battery or water damage, receiver module issues, «link» or interference.

This listing is for an NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs offer limited operating range and must be within a few inches of the vehicle in order to function. If you're far from your vehicle and press the key fob button, the car won't respond and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery in the coin cell (Part number CR2032) with a new one from a trusted brand like Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store or on the internet.

After you've replaced the battery of your coin cell, you can test it by standing in front of your fiat ducato remote key programming 500 and pressing the buttons. The car should blink its parking lights and the key fob should be able to operate the lock and unlock switches.

If your key fob still doesn't work even after replacing the battery, it could be water damage that prevents it from communicating with the module in your vehicle. Water damage can happen in many ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this isn't working, you'll require your fob to be reprogrammed either by an auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the circuit board of the fob, causing it to short out and eventually end up dying. It's not a good idea to submerge the fob in water however, don't give it up even if you accidentally drop the fob in water or fail to remove it from your pocket.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Test the fob afterward to determine if it's working. If the key still doesn't work, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and has not been programmed for your vehicle then you'll need to replace it completely. A professional locksmith for cars will be able to complete this process. The locksmith needs to cut the key to match the ignition on your vehicle. They'll also have to reprogram the fob in your car's system. This is a quick and cost-effective process which can be completed in the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop functioning is that it's out of range. The remote typically has a range of 30 feet or less, and if it's too far from your vehicle, it won't respond to your commands. You can easily solve this issue by moving the remote closer to your vehicle until it responds.

If your fob does not work after you replace the battery inside the coin, which is also called a "button", "watch" or "button" or "button", it could be a problem with the circuit board inside. Reprogramming the fob typically resolves this issue. There are instructions on how to do this for the majority of automobiles by searching YouTube or looking through the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they loose tension, it can prevent the coin battery from sitting properly and could cause your remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle due to software or hardware issues. This can cause a major problem, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some cases, they may need to reinstall the software in your body control module, too.

Interference

In addition to a dead coin battery the key fob could not be receiving or transmitting an signal due to interference. This could occur if the key fob is in proximity to a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob may not function may be a lack of connection to the buttons or the internal chip or water damage.

If the key fob has suddenly stopped working, suddenly or even after trying everything you can do at home to solve it e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable first then the positive cable. Then, reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers, which can help you get your key fob working again. If the issue persists, you should speak with an expert technician. They will be able to determine the root cause of any problems.