Replacement UPVC Door Handles

Find the perfect handle for your door, whether replacing your handles or adding security. These upvc handles are easy to install and conform to the 92mm centers required by multipoint locks.

The backplate fixing center and the dimensions of the lever/keyhole are the most important measurements. Compare these measurements to your existing measurements prior to placing an order.

Lever/Pad

Lever pad handles consist of a lever on one side, and a paddle-shaped handle on the other. These are designed to be used with key wind locks, however they can also be fitted to split spindle multipoint door locks (though you'll need a separate dual spindle lock case).

Our selection of upvc handle lever pads are available in a range of finishes. These will be listed in the drop-down list after you have selected the perfect handle for your door. Some styles of handles are not available in all finishes. You should always look over the technical drawings and size sections for the specific item you are looking to ensure you get the right size and fit.

When you are choosing the new set of lever pad door handles made of Upvc it is important to ensure that they correspond to the PZ (distance between the spindle of the handle and the centre of the cylinder hole) of your existing multipoint door locks, as they need to be in the same line to allow doors to remain locked, whether from the inside or the outside. Our handles are designed to fit a wide range of conventional cylinders, but it is always worth double-checking before purchasing.

If you wish to upgrade to dual spindle levers you will need to remove the handles you have already installed and take apart the lock case. This will require an extra split cylinder inline. You can purchase these separately. We have included a diagram of the technical aspects in the images of each product.

It is a good idea to loosen the screws that are holding your door brompton carry handle, and then inspect the mechanism. You may need to loosen the screws even more if they are not tight. Then you can take off the old handle and spindle and install your new door handle made of upvc. It is essential to ensure that the handle is in the proper position before fixing it. You can do this by placing your finger between the door frame and the handle to ensure that it's in the right position.

Lever/Lever

Lever door uvpc window handles operate a multi point lock using the Euro cylinder and are found on the majority of upvc double doors, aluminium doors and a few wooden doors. They feature an inside lever and a paddle on the outside and are usually supplied in two varieties. Sprung - These include a spring cassette inside the backplate that helps to bring the handle lever into an upright position. Non-sprung - These do not have a spring mechanism and will require manual pulled to bring the handle lever to the horizontal position.

To fix the door handle lever that is sliding you'll need to locate the hole or pin that is the detent access point. It's usually a small hole or protruding ring, or rectangle, that is located on the base of the handle plate. Once you have located it, loosen the set screw using the help of a screwdriver, and then remove it to release the lever to return to the horizontal position.

After the handle is positioned horizontally, you can install the screws. Make sure to tighten them so that the locking window handle stays attached to the base plate. You should also consider applying a threadlocking adhesive to the threads of the screw to increase the grip and prevent them from loosening over time.

There are a variety of reasons that door handles for levers droop. The most frequent reason is that the fixings have been too tightened and are putting strain on the bearings of the lever, and causing it to pull against the door's surface. It is also possible that the levers haven't been operated at the correct angle, which causes compression of the latch mechanism and prevents it from fully springing into motion.

A common cause of a spring lever not operating properly is the spring not being in the right position on the backplate. The simplest way to check this is to turn the handle to see whether it returns to the horizontal position.

If your door handles are loose it is essential to spot the issue fast, as this could lead to excessive wear on the screws and possibly to the handle falling off the base plate. It is also recommended to tighten any loose screws on a regular basis to prevent them from becoming looser.

Lever/Snib

These handles made of upvc are also referred to as 'Snib' handles and have a snib lever at the top of the lever that you can press down to lock your patio door handle locks in the event that you don't have an Dummy lock. They usually come with a Fullex 68PZ (that's 68mm between the spindle's centre and the lever or lock centre) door lock. We also stock a variety of other 68PZ door handles from various manufacturers, including Ferco and Fab & Fix.

Change your door handle is a cheap way to update your home, whether you're replacing handles that are in use or fitting new ones on doors that you've constructed in your home. There are various styles available for door handles made of upvc including the traditional lever on the backplate. Other choices include straight or curved short latches as well as knobs that resemble dummy knobs to lock multi-points. These are perfect for French doors.

Lever on backplate handles are often rectangular, but you can also find oval or circular versions, which are known as rose door handles. These door handles are characterized by a lever or knob that is attached to a backplate. The backplate can be removed to allow for concealed fixing.

There is a variety of chrome and colored finishes available for these handles that complement your door and other hardware, such as hinges, knobs and bolts. Some handles are supplied with grub screws that aid in the secure attachment of the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks and include a thumbturn turn and release mechanism, ideal to use on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the culprit in the event that your door handle is stuck open. There could be a variety of things that can cause this, the first being a simple lack of lubrication on the latch plate. It is possible to solve this issue by opening the door and spraying lubricant on the handle and lock. It could also be that the latch has come loose from the backplate. This is a more complicated issue that requires the assistance of a specialist.

A multipoint door handle system is a great solution to solve the issue of a sticking door handle. These handles are attached to the faceplate and are operated by either a thumb turn or key knob which activates the cam that locks the deadbolt. The handles are available in various sizes to fit different types of uPVC doors and are available in a variety of attractive finishes that complement existing hardware. These window handles for upvc can be purchased via the internet or from an authorized locksmith in your area. They are simple to install, with clear instructions.

To select a replacement handle set, you will be required to be aware of the PZ size of the cylinder. This is the distance in millimetres between the inner edge of the frame of the door and the centre of the handle hole. You'll also need the type of lock for your door, regardless of whether it's a mortise or hook lock. Once you know these measurements, the most efficient method to determine the right handles is to use the filter by brand on the website. This will narrow down your options, and you will then choose the appropriate size from there.